1-1/2 Liter capacity. Auto shut off with boil-dry protection. Keep warm switch. 360-Degree cordless element. Easy to pour spout. Cord storage. On/off indicator light. Works in 120 Volts.

Using your Electric Kettle

1. Position the power base on a flat, heat resistant surface, as close as

possible to a power outlet.

2. Follow cord routing in power base according to exit patterns. Proper

cord routing will result in the power base laying flat when kettle is

placed in base. DO not operate kettle if power base is not flat. If

power base is not flat, remove kettle from power base and repeat

cord placement instructions.

3. To fill with water, remove the lid. Fill the electric kettle with water

to below the “MAX” water level mark. NOTE: Do not exceed the

“MAX” water level mark indicated on the electric kettle.

4. Plug the electric cord into an electric outlet. Turn the switch ON

by pushing down on the on/off switch. The on/off light will light to

indicate the unit is on. The water will heat and the electric kettle will

switch off automatically when the water boils. NOTE: Ensure the

ON/OFF switch is clear of obstructions and the lid is firmly closed.

The electric kettle will not turn off automatically if the ON/OFF

switch is constrained, or if the lid is left open.

5. Carefully lift the kettle from the power base and pour the hot water.

6. The kettle will not re-boil until the on/off switch is again switched

ON. Wait 25 seconds, allowing kettle to cool down, then switch ON.

Filter removal/cleaning/refitting

Important: The kettle must be switched off, disconnected from the

power outlet and allowed to cool down completely prior to removing

or refitting the filter. Do not use excessive force, as this might damage

the filter or the lid.

1. Empty the kettle and lift lid.

2. Grip the top part of the filter with index finger and thumb and

pull upwards. You may have to hold kettle while removing filter.

Caution: Keep fingers clear of mesh. Pressing into mesh may

damage filter.

3. To clean the filter, rinse under a tap while brushing it gently wit

a soft brush.

4. To refit filter, once again hold filter with index finger and thumb.

Gently push filter back into the kettle until you hear a click. The

filter is now reattached. Gently tug on filter to ensure filter is

attached properly.

5. Rinse out kettle with fresh water and it’s ready for use.

Care and cleaning of your electric kettle

1. Mineral deposits in tap water may cause scale deposits to form

inside the electric kettle after frequent use. To remove this scale

build-up, fill the kettle with a solution of 3 cups of white vinegar

and 3 cups water. Let sit overnight.

2. Empty the vinegar solution from the electric kettle. Remove any

stain remaining inside by rubbing with a damp cloth.

3. Fill the electric kettle with clean water. Place kettle on power base

and bring to a boil, then discard water. Repeat and the electric kettle

will be ready to use.

4. The electric kettle will not operate again until the on/off switch is

pressed downward.

5. Always remove kettle from power base and disconnect power base

from electrical outlet before cleaning. Do not immerse kettle or

power base in water or other liquid.

6. The outside of the electric kettle can be wiped with a soft damp cloth.

NOTE: Never use any chemical, steel wool, or abrasive cleaners to

clean any part of the kettle, including the power base.

Product Features

• Stainless-steel electric kettle quickly boils up to 1-1/2 liters of water
• 360-degree power base for graceful cord-free serving; features keep-warm function
• Water-level indicator; concealed element; automatic shut-off with boil-dry protection
• Non-drip spout with removable fine-mesh filter; stay-cool handle; cord storage , Measures approximately 8-2/3 by 6-8/9 by 10-3/5 inches
• Kindly refer the instruction steps (PDF) given below for the troubleshooting steps.